HomeTile AdhesiveREYNOSTYLE TAC 1T 307

REYNOSTYLE TAC 1T 307

WHITE CEMENT BASED MODIFIED POLYMER TILE ADHESIVE

Tile Adhesive Cementitious complies to the adhesion requirements of IS 15477: 2019 Type 3T “Specification for Adhesives for use with Ceramic Tiles.” Also complies with EN C2TE Classification.

Description

Product Description

FAB ( Features, Benefits & Advantages )

  1. White high polymer modified cement-based wall & floor tile adhesive. Suitable for fixing marble, tiles and natural stones in interior and exterior situations, including swimming pools and other wet areas due to good underwater shear-bond.
  2. For installation of ceramic / clay / vitrified / basalt / glass mosaic and porcelain / all natural stone tiles with porosity less than or equal to 3 percent.
  3. Can also be used as slurry bond adhesive in wet-on-wet applications, tile on tile applications.
  4. For installation of large dimensions not greater than 1000mm x 1000 mm on wall substrates like plaster or concrete.
  5. To install tiles on to various substrates like Concrete: Concrete Masonry, VDF / Trimix Concrete, Cement Mortar Beds, Cement Plaster; Existing Vitrified Tile & Ceramic Tile; Brick Masonry; Cement Terrazzo; Existing Natural Stone, Cement Backer Board, Calcium Silicate Board, Gypsum Wallboard.

Coverage

  1. Approx. 50 to 55 sq. ft. per 20 Kg pack, using 6mm x 6mm square notched trowel for a bed of 3mm.
  2. Coverage will depend on the nature and flatness of the surface and the method of application. For good coverage, it is must that all surfaces are smooth, plumb, level and free from defects and undulations.

Mixing

  1. Add Tile Adhesive to clean water
  2. Mix thoroughly by hand or with a slow speed mixer to obtain slump free mortar for a trowel able consistency.
  3. Use approximately 5 litres of water for 20 kg of powder.
  4. The adhesive is immediately ready-for-use and has a pot life of 2.0 hours.
  5. No further water should be added.
  6. Allow adhesive to slake for 5 minutes.

 

Note: Addition of REYNOBOND Latex partially or completely replacing water increases the bond strength and
flexibility of mortar.

Technical Data

IS Data
Property: Test method Requirement Typical Values
Tensile Adhesion

Dry Conditions –

Annex A (Clause5.1)

Minimum1.5 N/mm² 1.5-1.65 N/mm²
Wet Conditions –

Annex A (Clause5.1)

Minimum1.00 N/mm² 1.10-1.20 N/mm²
Shear Adhesion

Dry Conditions –

Annex B (Clause 5.2)

Minimum1.5 N/mm² 1.60-1.70 N/mm²
Heat Ageing –

Annex B (Clause 5.2)

Minimum1.00 N/mm² 1.10-1.20 N/mm²
Wet Conditions –

Annex B (Clause 5.2)

Minimum1.00 N/mm² 1.15-1.25 N/mm²

Slip resistance-

Annex E (Clause 5.5)

≤ 0.5 mm 0.35-0.45 mm

* For further detail, Please refer to Technical Data Sheet

REYNOSTYLE TAC 1T 307
REYNOSTYLE TAC 1T 307
Tile-Adhesive
Tile Cleaner

Additional information

Colour

White

Working Properties at

21° C

REYNOSTYLE TAC 3T 325 W Adhesive mixed

Water

Open Time

20 minutes

Pot Life

3 – 4 hours

Adjustment Time

20 Minutes

Time to Heavy Traffic

16 – 24 hours

Packaging

20 Kg

Reviews

There are no reviews yet.

Be the first to review “REYNOSTYLE TAC 1T 307”

Your email address will not be published. Required fields are marked *

You may also like…